3,218
edits
Difference between revisions of "Bearings"
Jump to navigation
Jump to search
no edit summary
(Created page with "Category:Mechanical Components{{Knoppen}} <noinclude><!------------------------------------------------ * READ THIS FIRST * Only edit this page if you can improve the conten...") |
|||
| Line 1: | Line 1: | ||
[[Category:Mechanical Components]]{{Knoppen}} | [[Category:Mechanical Components]]{{Knoppen}} | ||
[[File:Bearing animation.gif|thumb|right|Animation of Bearings]] | |||
* | [[File:Bearing1.jpg|thumb|right|Bearings]] | ||
* | '''Bearing''' is a machine element that constrains relative motion between moving parts to only the desired motion. The design of the bearing may, for example, provide for free linear movement of the moving part or for free rotation around a fixed axis; or, it may prevent a motion by controlling the vectors of normal forces that bear on the moving parts. Bearings are classified broadly according to the type of operation, the motions allowed, or to the directions of the loads applied to the parts.The term bearing is derived from the verb to bear; a bearing being a machine element that allows one part to bear another. The simplest bearings are bearing surfaces, cut or formed into a part, with varying degrees of control over the form, size, roughness and location of the surface. Other bearings are separate devices installed into a machine or machine part. The most sophisticated bearings for the most demanding applications are very precise devices; their manufacture requires some of the highest standards of current technology. | ||
* | |||
==Common== | |||
By far, the most common bearing is the plain bearing, a bearing which uses surfaces in rubbing contact, often with a lubricant such as oil or graphite. A plain bearing may or may not be a discrete device. It may be nothing more than the bearing surface of a hole with a shaft passing through it, or of a planar surface that bears another ; or it may be a layer of bearing metal either fused to the substrate (semi-discrete) or in the form of a separable sleeve (discrete). With suitable lubrication, plain bearings often give entirely acceptable accuracy, life, and friction at minimal cost. Therefore, they are very widely used. | |||
However, there are many applications where a more suitable bearing can improve efficiency, accuracy, service intervals, reliability, speed of operation, size, weight, and costs of purchasing and operating machinery.Thus, there are many types of bearings, with varying shape, material, lubrication, principle of operation, and so on. | |||
==Principles of operation== | |||
There are at least six common principles of operation: | |||
* plain bearing, also known by the specific styles: bushings, journal bearings, sleeve bearings, rifle bearings | |||
* rolling-element bearings such as ball bearings and roller bearings | |||
* jewel bearings, in which the load is carried by rolling the axle slightly off-center | |||
* fluid bearings, in which the load is carried by a gas or liquid | |||
* magnetic bearings, in which the load is carried by a magnetic field | |||
* flexure bearings, in which the motion is supported by a load element which bends. | |||
==Motions== | |||
Common motions permitted by bearings are: | |||
* axial rotation e.g. shaft rotation | |||
* linear motion e.g. drawer | |||
* spherical rotation e.g. ball and socket joint | |||
* hinge motion e.g. door, elbow, knee | |||
==Friction== | |||
Reducing friction in bearings is often important for efficiency, to reduce wear and to facilitate extended use at high speeds and to avoid overheating and premature failure of the bearing. Essentially, a bearing can reduce friction by virtue of its shape, by its material, or by introducing and containing a fluid between surfaces or by separating the surfaces with an electromagnetic field. | |||
* By shape, gains advantage usually by using spheres or rollers, or by forming flexure bearings. | |||
* By material, exploits the nature of the bearing material used. | |||
* By fluid, exploits the low viscosity of a layer of fluid, such as a lubricant or as a pressurized medium to keep the two solid parts from touching, or by reducing the normal force between them. | |||
* By fields, exploits electromagnetic fields, such as magnetic fields, to keep solid parts from touching. | |||
Combinations of these can even be employed within the same bearing. An example of this is where the cage is made of plastic, and it separates the rollers or balls, which reduce friction by their shape and finish. | |||
==Loads== | |||
Bearings vary greatly over the size and directions of forces that they can support. | |||
Forces can be predominately radial, axial (thrust bearings) or bending moments perpendicular to the main axis. | |||
==Speeds== | |||
Different bearing types have different operating speed limits. Speed is typically specified as maximum relative surface speeds, often specified ft/s or m/s. Rotational bearings typically describe performance in terms of the product DN where D is the diameter (often in mm) of the bearing and N is the rotation rate in revolutions per minute. | |||
Generally there is considerable speed range overlap between bearing types. Plain bearings typically handle only lower speeds, rolling element bearings are faster, followed by fluid bearings and finally magnetic bearings which are limited ultimately by centripetal force overcoming material strength. | |||
==Play== | |||
Some applications apply bearing loads from varying directions and accept only limited play or slop as the applied load changes. One source of motion is gaps or play in the bearing. For example, a 10 mm shaft in a 12 mm hole has 2 mm play. | |||
Allowable play varies greatly depending on the use. As example, a wheelbarrow wheel supports radial and axial loads. Axial loads may be hundreds of newtons force left or right, and it is typically acceptable for the wheel to wobble by as much as 10 mm under the varying load. In contrast, a lathe may position a cutting tool to ±0.02 mm using a ball lead screw held by rotating bearings. The bearings support axial loads of thousands of newtons in either direction, and must hold the ball lead screw to ±0.002 mm across that range of loads. | |||
==Stiffness== | |||
A second source of motion is elasticity in the bearing itself. For example, the balls in a [[Ball Bearings]] are like stiff rubber, and under load deform from round to a slightly flattened shape. The race is also elastic and develops a slight dent where the ball presses on it. | |||
The stiffness of a bearing is how the distance between the parts which are separated by the bearing varies with applied load. With rolling element bearings this is due to the strain of the ball and race. With fluid bearings it is due to how the pressure of the fluid varies with the gap. | |||
==Maintenance and lubrication== | |||
Many bearings require periodic maintenance to prevent premature failure, although some such as fluid or magnetic bearings may require little maintenance.Most bearings in high cycle operations need periodic lubrication and cleaning, and may require adjustment to minimise the effects of wear. | |||
Bearing life is often much better when the bearing is kept clean and well-lubricated. However, many applications make good maintenance difficult. For example bearings in the conveyor of a rock crusher are exposed continually to hard abrasive particles. Cleaning is of little use because cleaning is expensive, yet the bearing is contaminated again as soon as the conveyor resumes operation. Thus, a good maintenance program might lubricate the bearings frequently but never clean them. | |||
===Packing=== | |||
Some bearings use a thick grease for lubrication, which is pushed into the gaps between the bearing surfaces, also known as packing. The grease is held in place by a plastic, leather, or rubber gasket that covers the inside and outside edges of the bearing race to keep the grease from escaping. | |||
Bearings may also be packed with other materials. Historically, the wheels on railroad cars used sleeve bearings packed with waste or loose scraps cotton or wool fiber soaked in oil, then later used solid pads of cotton. | |||
===Ring oiler=== | |||
Bearings can be lubricated by a metal ring that rides loosely on the central rotating shaft of the bearing. The ring hangs down into a chamber containing lubricating oil. As the bearing rotates, viscous adhesion draws oil up the ring and onto the shaft, where the oil migrates into the bearing to lubricate it. Excess oil is flung off and collects in the pool again. | |||
===Splash lubrication=== | |||
Some machines contain a pool of lubricant in the bottom, with gears partially immersed in the liquid, or crank rods that can swing down into the pool as the device operates. The spinning wheels fling oil into the air around them, while the crank rods slap at the surface of the oil, splashing it randomly on the interior surfaces of the engine. Some small internal combustion engines specifically contain special plastic flinger wheels which randomly scatter oil around the interior of the mechanism. | |||
===Pressure lubrication=== | |||
For high speed and high power machines, a loss of lubricant can result in rapid bearing heating and damage due to friction. Also in dirty environments the oil can become contaminated with dust or debris that increases friction. In these applications, a fresh supply of lubricant can be continuously supplied to the bearing and all other contact surfaces, and the excess can be collected for filtration, cooling, and possibly reuse. Pressure oiling is commonly used in large and complex internal combustion engines in parts of the engine where directly splashed oil cannot reach, such as up into overhead valve assemblies.High speed turbochargers also typically require a pressurized oil system to cool the bearings and keep them from burning up due to the heat from the turbine. | |||
==Sources== | |||
[http://en.wikipedia.org/wiki/Bearing_(mechanical) Wikipedia Bearing] | |||