Roller Gates - Revision history

Admin at 14:16, 23 June 2014

2014-06-23T14:16:50Z

← Older revision		Revision as of 08:16, 23 June 2014
Line 1:		Line 1:
	[[Category:Valves]]{{Knoppen}}		[[Category:Valves]]{{Knoppen}}
	[[File:Roller gates1.jpg\|thumb\|right\|Roller Gates]]		[[File:Roller gates1.jpg\|thumb\|right\|Roller Gates]]
	~~[[File:Roller gates.jpg\|thumb\|right\|Roller Gates]]~~
	'''Roller Gates''' are designed to control flow through large waterway openings where economy and ease of operation are important. They may be designed as either upward or downward opening. A roller or fixed wheel gate consists of a fabricated steel slide with cast iron rollers and rubber seals. The gate leaf is a box-like design of welded construction. It varies in width and height as required by the size of the opening in the concrete and varies in thickness depending on the depth of water. Recesses at the sides of the gate opening are provided with rails and with contact faces for side seals. The thrust developed from water pressure against the gate is transmitted through the rollers to the rails and into the structure. The lift capacity required to open the gate under maximum operating conditions is minimized as the thrust caused by the water pressure is transferred to rolling friction .		'''Roller Gates''' are designed to control flow through large waterway openings where economy and ease of operation are important. They may be designed as either upward or downward opening. A roller or fixed wheel gate consists of a fabricated steel slide with cast iron rollers and rubber seals. The gate leaf is a box-like design of welded construction. It varies in width and height as required by the size of the opening in the concrete and varies in thickness depending on the depth of water. Recesses at the sides of the gate opening are provided with rails and with contact faces for side seals. The thrust developed from water pressure against the gate is transmitted through the rollers to the rails and into the structure. The lift capacity required to open the gate under maximum operating conditions is minimized as the thrust caused by the water pressure is transferred to rolling friction .

Kodiyath at 18:59, 13 January 2013

2013-01-13T18:59:34Z

← Older revision		Revision as of 12:59, 13 January 2013
Line 9:		Line 9:
	==Types of Roller Gates==		==Types of Roller Gates==
	There are two types of roller gates: the overflow type for use where the water depth is the same as the height of the gate slide; and the breastwall type where water is considerably deeper than the height of the gate and/or where complete closure of the opening is required.		There are two types of roller gates: the overflow type for use where the water depth is the same as the height of the gate slide; and the breastwall type where water is considerably deeper than the height of the gate and/or where complete closure of the opening is required.


	===Overflow Type===		===Overflow Type===
Line 21:		Line 20:

	==Operation==		==Operation==
	Roller gates are usually operated with threaded stems and manual or electric lifts. Single stems are used when the gate width does not exceed twice the height. [[Gates ]]that are very wide compared to their height should have tandem stems. Very tall gates may be equipped with tandem stems and traveling stem guides in order to keep the stem size, yoke and lift in an optimum cost range. Roller gates may also be cylinder operated; however, very tall or very wide gates requiring tandem cylinders are not recommended due to synchronization or alignment problems. Another way of operating gates is with a rope hoist . Close attention must be paid to closing friction loads since the gate may require a ballast to close against the operating head. A roller gate may also serve as a removable bulkhead using an overhead crane. Lifts may be mounted on the concrete structure and are available with pedestals or wall brackets. More commonly, there is no concrete structure above the gate opening. In this case, the lift or tandem lifts are mounted on a head frame which can be either attached to the structure or be attached to the extended slot assemblies .		Roller gates are usually operated with threaded stems and manual or electric lifts. Single stems are used when the gate width does not exceed twice the height. [[Gates]] that are very wide compared to their height should have tandem stems. Very tall gates may be equipped with tandem stems and traveling stem guides in order to keep the stem size, yoke and lift in an optimum cost range. Roller gates may also be cylinder operated; however, very tall or very wide gates requiring tandem cylinders are not recommended due to synchronization or alignment problems. Another way of operating gates is with a rope hoist . Close attention must be paid to closing friction loads since the gate may require a ballast to close against the operating head. A roller gate may also serve as a removable bulkhead using an overhead crane. Lifts may be mounted on the concrete structure and are available with pedestals or wall brackets. More commonly, there is no concrete structure above the gate opening. In this case, the lift or tandem lifts are mounted on a head frame which can be either attached to the structure or be attached to the extended slot assemblies .


	==Applications==		==Applications==

Kodiyath at 18:57, 13 January 2013

2013-01-13T18:57:37Z

@@ Line 1: / Line 1: @@
 [[Category:Valves]]{{Knoppen}}
 Roller gates
-  are large cylinders that move in an angled slot. They are hoisted with a chain and have a cogged design that interfaces with their slot.

Kodiyath at 17:49, 13 January 2013

2013-01-13T17:49:44Z

← Older revision		Revision as of 11:49, 13 January 2013
Line 1:		Line 1:
	[[Category:Valves]]{{Knoppen}}		[[Category:Valves]]{{Knoppen}}
	~~<noinclude><!------------------------------------------------~~
	* READ THIS FIRST		Roller gates
	* Only edit this page if you can improve the content.		are large cylinders that move in an angled slot. They are hoisted with a chain and have a cogged design that interfaces with their slot.
	* Improper use of this page will lead to permanent banning.
	* Please do not edit the sponsored link on the top right corner.
	* Please start editing this page after the /noinclude
	* -------------------------------------------------></noinclude>
	~~This page is still empty. If you know something about this product, please share your knowledge~~ with ~~others~~.

Admin: Created page with "Category:Valves{{Knoppen}}