Flexible Couplings - Revision history

Admin at 14:57, 12 March 2014

2014-03-12T14:57:36Z

← Older revision		Revision as of 08:57, 12 March 2014
Line 1:		Line 1:
	[[Category:Piping]]{{Knoppen}}		[[Category:Piping]]{{Knoppen}}
	~~<noinclude><!------------------------------------------------~~
	* READ THIS FIRST
	* Only edit this page if you can improve the content.
	* Improper use of this page will lead to permanent banning.
	* Please do not edit the sponsored link on the top right corner.
	* Please start editing this page after the /noinclude
	* -------------------------------------------------></noinclude>
	[[File:Flexible coupling.jpg\|thumb\|right\|Flexible Couplings]]		[[File:Flexible coupling.jpg\|thumb\|right\|Flexible Couplings]]
	[[File:Flexible coupling1.jpg\|thumb\|right\|Flexible Couplings]]		[[File:Flexible coupling1.jpg\|thumb\|right\|Flexible Couplings]]
	'''Flexible couplings''' are used to transmit torque from one shaft to another when the two shafts are slightly misaligned. Flexible couplings can accommodate varying degrees of misalignment up to 3° and some parallel misalignment. In addition, they can also be used for vibration damping or noise reduction.A coupling designed to allow a limited angular movement between the axes of two waveguides.		'''Flexible couplings''' are used to transmit torque from one shaft to another when the two shafts are slightly misaligned. Flexible couplings can accommodate varying degrees of misalignment up to 3° and some parallel misalignment. In addition, they can also be used for vibration damping or noise reduction.A coupling designed to allow a limited angular movement between the axes of two waveguides.


	==Types==		==Types==
	The following types of flexible couplings are the most common.		The following types of flexible couplings are the most common.

	===Jaw Couplings===		===Jaw Couplings===
	There are 3 types of jaw couplings: Straight Jaw, Curved Jaw and Jaw In-Shear . All couplings consist of three basic components: two hubs and one insert. The straight jaw couplings are the standard style and can operate in torque ranges from 3.5 ft-lb (4.7 Nm) to 170,004 ft-lb (230,233 Nm). Curved jaw couplings are similar to straight jaw, but the teeth of the hubs and insert are curved to accommodate additional torque. These couplings can transmit torques between 67 ft-lb (91 Nm) and 247,800 ft-lb (335,590 Nm). The jaw in-shear coupling is similar to the other two, but has an additional component. A locking ring is used to secure a split insert. The advantage of this style is the insert can be replaced without moving the two hubs. Jaw in-shear couplings can transmit torques from 335 ft-lb (454 Nm) to 183,333 ft-lb (248,284 Nm). All of the jaw type couplings can accommodate angular misalignment up to 1°.		There are 3 types of jaw couplings: Straight Jaw, Curved Jaw and Jaw In-Shear . All couplings consist of three basic components: two hubs and one insert. The straight jaw couplings are the standard style and can operate in torque ranges from 3.5 ft-lb (4.7 Nm) to 170,004 ft-lb (230,233 Nm). Curved jaw couplings are similar to straight jaw, but the teeth of the hubs and insert are curved to accommodate additional torque. These couplings can transmit torques between 67 ft-lb (91 Nm) and 247,800 ft-lb (335,590 Nm). The jaw in-shear coupling is similar to the other two, but has an additional component. A locking ring is used to secure a split insert. The advantage of this style is the insert can be replaced without moving the two hubs. Jaw in-shear couplings can transmit torques from 335 ft-lb (454 Nm) to 183,333 ft-lb (248,284 Nm). All of the jaw type couplings can accommodate angular misalignment up to 1°.

	===Gear Couplings===		===Gear Couplings===
	Gear couplings use gear teeth to transmit torque from one shaft to another. The coupling accommodates misalignment through the clearance between the inner and outer gear teeth.This allows for the coupling to transmit high torques at high speed when the coupling is balanced. The coupling can transmit torques from 2,500 in-lb (208 ft-lb or 282 Nm) to 47,269,000 in-lb (393,908 ft-lb or 533,462 Nm) and has an angular misalignment capacity of 3°.		Gear couplings use gear teeth to transmit torque from one shaft to another. The coupling accommodates misalignment through the clearance between the inner and outer gear teeth.This allows for the coupling to transmit high torques at high speed when the coupling is balanced. The coupling can transmit torques from 2,500 in-lb (208 ft-lb or 282 Nm) to 47,269,000 in-lb (393,908 ft-lb or 533,462 Nm) and has an angular misalignment capacity of 3°.

	===Grid Couplings===		===Grid Couplings===
	Grid couplings use two slotted hubs with a steel grid running between them to transmit torque. The coupling flexes by allowing the grid to slide along the slots in the hubs. Grid couplings can only accommodate 1/3° misalignment and transmit torque from 422 in-lbs to 2,700,000 in-lb (3,656,555 Nm).		Grid couplings use two slotted hubs with a steel grid running between them to transmit torque. The coupling flexes by allowing the grid to slide along the slots in the hubs. Grid couplings can only accommodate 1/3° misalignment and transmit torque from 422 in-lbs to 2,700,000 in-lb (3,656,555 Nm).

	===Fluid Couplings===		===Fluid Couplings===
	Fluid couplings are not necessarily a type of flexible coupling, but are used in association with flexible couplings. Fluid couplings allow motors to start up under a low load. The fluid coupling uses two wheels and an outer shell to transmit torque. Because the coupling transmits the torque hydrodynamically, the coupling also provides overload protection and shock absorbtion. A flexible coupling is added to a fluid coupling to allow for misalignment.		Fluid couplings are not necessarily a type of flexible coupling, but are used in association with flexible couplings. Fluid couplings allow motors to start up under a low load. The fluid coupling uses two wheels and an outer shell to transmit torque. Because the coupling transmits the torque hydrodynamically, the coupling also provides overload protection and shock absorbtion. A flexible coupling is added to a fluid coupling to allow for misalignment.

	===Torsional Couplings===		===Torsional Couplings===
	There are many different types of torsional couplings. Most couplings use a rubber element to transmit torque between two hubs. The rubber damps any vibrations moving from one shaft to the other. Torsional couplings are made to adapt to shafts, flywheels or universal joints.		There are many different types of torsional couplings. Most couplings use a rubber element to transmit torque between two hubs. The rubber damps any vibrations moving from one shaft to the other. Torsional couplings are made to adapt to shafts, flywheels or universal joints.

Kodiyath at 15:00, 1 January 2013

2013-01-01T15:00:11Z

@@ Line 7: / Line 7: @@
 * Please start editing this page after the /noinclude
 * -------------------------------------------------></noinclude>
-This page is still empty. If you know something about this product, please share your knowledge with others.
+[[File:Flexible coupling.jpg|thumb|right|Flexible Couplings]]

Admin: Created page with "Category:Piping{{Knoppen}}